The highest efficiency in the use of Ceramizer is achieved by® strictly following the recommendations and instructions.
- Ceramizer® can be mixed with any type of oil and used for all types of two-stroke engines.
- An underestimated dose of Ceramizer will not bring the® expected results.
- An inflated (e.g. 2 x larger) dose of Ceramizer does® not cause any side effects.
- For an exhausted (over 50% wear) engine, it is recommended to additionally use Ceramizer® by applying it to the cylinder walls through the hole after the unscrewed candle.
THE PACKAGE CONTAINS:
- This manual.
- One dispenser of an easily oil-soluble preparation with a net weight of 4 g.
RECOMMENDATIONS:
- We recommend measuring the pressure of the compression end (before and after machining) in the cylinders of the engine – to confirm the effectiveness of the Ceramizer®
- Ceramizer can be used after arrival, i.e. after 1000 km or 20 mth (operating hours).
- Use prophylactically to protect the engine from the effects of friction, significantly extending its service life and trouble-free operation time.
- Can be used with any type of oil.
- Can be used in two-stroke engines of any machines and devices.
- Can be used in motors with nikasil.
STATEMENT:
Stage I – Ceramizer® up to 1 liter of oil.
- Mix ceramizer dose® with 1 l of oil.
- Use a® liter of oil with Ceramizer, adding to the fuel in the proportion according to the recommendations of the engine manufacturer.
- Before each addition of a portion of oil to the fuel or automatic lubrication tank – the oil with Ceramizer® must be shaken repeatedly.
- Operate the engine with a mixture of fuel and oil with Ceramizer® for at least 700 km avoiding high revs and overloads.
- After consuming 1 liter of oil, the fuel filter should be organoleptically checked and if it gets dirty, it should be replaced.
Stage II – Ceramizer® to the cylinder.
- Warm up the engine to an operating temperature of 80 to 90 degrees C (e.g. after driving or at least after 10 minutes of engine idling).
- Turn off the engine
- Unscrew the spark plug.
- Set the piston at the upper turning point
- Apply 1/2 dose of Ceramizer® through the hole after the unscrewed candle (trying to distribute Ceramizer® over the walls of the cylinder).
- Activate the clearance in the vehicle/device.
- Without screwing in the candle, turn the crankshaft several dozen times (e.g. using a starter for a few seconds or in the case of small motors – a drill)
- Apply the remaining 1/2 dose of Ceramizer® through the hole after the unscrewed candle (trying to distribute Ceramizer® over the cylinder walls) and repeat points 6 and 7.
- Screw in the candle.
- Start the engine, leave at idle for about 15 minutes.
Both stages of using Ceramizer® are recommended to be performed in the same application cycle.
COMMENTS:
- In case of mechanical damage to the engine (eg. cracked piston ring, deep scratches on the smooth
cylinder, etc.) defects should be repaired, after which Ceramizer® treatment should be applied. - In the case of engine overhaul, you should drive 1000-2000 km from the moment of renovation and only then use Ceramizer®.
- Ceramizer® does not regenerate places where there is friction of rubber or plastics against metal.
- Dispensers/syringes that have a small leakage from under the plunger are also considered correct
Filled.
SAFETY:
- The product is safe in accordance with current EU standards.
- Ceramizer® is oil neutral, it can be used for any oil – it does not change the physicochemical and rheological parameters of the oil (this is confirmed by the expertise of the Air Force Institute of Technology NO. 6/55/08)
- Store below +40 oC. If the storage temperature exceeds +40oC, the product can be sedimented, then the preparation should be shaken and cooled to a temperature below +40oC to use it safely.
- It does not contain Teflon or molybdenum.
- Ceramizer® causes an increase in reliability, which ensures increased safety of travel and use of devices.
- Keep out of reach of children.
RESEARCH:
Effectiveness confirmed by tests and opinions of users posted on the www.ceramizer.pl.
EFFECTIVENESS:
The ceramic-metal layer produced remains effective and durable for about 15,000 km of mileage or 300 km
Mth. After this mileage, it is recommended to re-apply Ceramizer® 2T – to a two-stroke engine.
Download manual CM-2T (PDF format)