Instruction for 4-stroke engines (CS)
Highest effectiveness in use of Ceramizer® is reached when complying strictly with recommendations and instruction.
- During the whole process of ceramization (1500 km / 900 miles) oil should not be changed. The next oil change should be done when normally required by the servicing program.
- Ceramizer® is compatible with all types of oil and for combustion engines (petrol engines, supplied by gas, Diesel, turbocharged engines and these with catalytic converters).
- A lowered dose of Ceramizer® will not give the expected results.
- Increased dose doesn't cause any side effects, it only lengthens the process of cermet creation.
- For the engine which is very worn out the dosaging of Ceramizer should be increased by 50%. In case of "taking" the oil in an amount exceeded 0.4 l/1000 km, the dosaging of Ceramizer should be doubled.
- The dosaging of Ceramizer® should also be doubled for engines used in sports and extreme conditions of exploitation.
DOSAGING - amount of doses, needed for ceramization of friction surfaces presented below:
| Capacity of oil in the engine (in litres) --> | 2-8 l | 9-16 l | 17-24 l | 25-33 l |
| Mileage : 5- 50 000 km or 3-30000 miles | 1/2 dose | 1 dose | 2 doses | 3 doses |
| Mileage: 50 000- 300 000 km or 30 000- 180 000 miles | 1 dose | 2 doses | 3 doses | 4 doses |
| Mileage: over 300 000 km or 180 000 miles | 2 doses | 3 doses | 4 doses | 5 doses |
PACKAGE includes:
- One dose of Ceramizer CS with net mass of 4 g.
- Instruction of use
RECOMMENDATIONS:
- Measure the compression pressure (before and after treatment) in cylinders of the engine - in order to confirm the effectiveness of Ceramizer and obtain tangible effects.
- Apply at any stage , preferably directly at the oil change for optimally long period of driving with Ceramizer®.
- Use primarily for preventive reasons to protect the engine against the effects of friction, significantly prolonging its life..
- Ceramizer® can be used with any type of oil.
- During the full processing (1500 km) do not change oil.
- Use together with Ceramizer® for gearboxes, rear axles, power steering, fuel purifier.
- Ceramizer® can be used for any machines and factory units after consulting the Producer.
INSTRUCTION:
- Warm the engine up to 80-90 oC, by driving or keeping the engine going on the idle gear for at least 10 minutes.
- Turn the engine off.
- Unscrew the cap oil reservoir and pour the content of the syringe into the engine's inlet.
- Turn the cap oil reservoir back on.
-
Turn the engine on and leave it on the idle gear for 15 minutes. -
Drive carefully for 200 km / 125 miles (not necessarily at one time), not exceeding 2700 rotations/minute (the lower the rpm is, the higher friction in engine and the more effective creation of the coating of cermet is).
Note: 200 km / 125 miles can be replaced by leaving the engine working for 4 hours on the idle gear. One hour on the idle gear – corresponds to 50 km / 30 miles drive. - Engines which parameters are expressed in moto hours (mth) should be exploited within 5 mth (not necessarily at one time) not exceeding 2700 rotations/minute (rpm).
- Upon reaching 200 km / 125 miles or after 4 hours on the idle gear you can drive without rotations' limitation. The metal-ceramic layer develops still up to 1500 km / 900 miles in normal operating conditions. During this time oil shouldn't be changed.
- Engines which parameters are expressed in moto hours (mth) can be exploited without limitations after reaching 5 mth. The process of ceramization is completed after 30 mth.
- We recommend to double the dosage of Ceramizer® presented in the instruction chart, if the engine absorbs oil. The first dose should be applied according to the directions for use, then after 500 km / 300 miles the second one should be applied in the same way.
REMARKS:
- If any teflon or molybdenum components had been added to oil before, we recommend to exchange this oil and to clean mechanism before appying Ceramizer® . Otherwise its effectiveness will be reduced and process of the cermet creation will be lengthened.
- In case of any mechanical damages of the engine e.g. cracked or scorched piston ring, leaky valve, deep scratches on the cylinder etc., they should be repaired before adding Ceramizer®.
- Ceramizer® does not recondition any places where friction of rubber or plastic with metal parts occurs.
- In case of engines without automatic adjustment of valve clearance, if after Ceramizer® treatment during 1500 km /900 miles, clatters of valves are heard, a regulation should be performed.
- If the engine is equipped with a centrifugal oil filter, it should be cleaned before applying Ceramizer®, and it is recommended to turn off the oil circulation while tooling, by using a tube (if possible). In these types of filters molecules tend to settle down, therefore the amount that reaches friction surfaces is reduced.
- The syringes are usable and the product is fully functional even if a small leakage of product under the pusher is noticed.
SAFETY:
- This product is safe in accordance with the UE (91/155/EEC) norm.
- Store at a temperature below +40 oC.
- Does not clog oil filters or oil ducts.
- Does not contain molybdenum or teflon. Can be safely used in engines with DPF.
- Keep away from children.
RESEARCH:
Effectiveness confirmed by multiple independent tests.
EFFECTIVENESS:
Ceramizer provides protection against wear and tear for minimum of 70 000 km/43 000 miles. Ceramizer® can be used again after this mileage.
